Perun AB++ johdotettuna
Perun AB++ johdotettuna
Perun AB++ johdotettuna

Perun AB++ johdotettuna

Hinta: 54,90 €
Verkkokauppa: Ei saatavilla. Kysy saatavuus!
Oulun myymälä: Ei saatavilla

Tilaa saapumisilmoitus sähköpostiisi, niin saat heti tiedon kun tuotetta on jälleen saatavilla.

Perun  AB++, johdotettuna 


AB++ is an on-wire mosfet, channeling the power from the battery to the motor through a specialized high-power transistor, instead of delicate mechanical switches, increasing reliability and replica performance. It also enhances your replica by adding many new, useful features.

Works with 7.4V, 11.1V and 14.8V batteries. Comes almost fully pre-wired, with only few easy soldering joints needed to install the mosfet.

Features:

Electronic burst

Active brake with adjustable braking power

Precocking (with spring release feature)

Rate of fire reduction

DMR mode

Low battery voltage alarm

Programming supported with a multicolor LED diode

Diagnostic system

Electronic resettable fuse


Feature description

Electronic burst - Change auto to an electronically controlled burst to save your ammo and increase realism!

Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).

Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger while simultaneously holding button on the unit. A shot will be fired, with no precocking and fully braked.

Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.

Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery if a short circuit or blocked motor is detected.


Programming of all the settings is done solely by using trigger and a button on the device, in an easily memorable and quick sequences. Programming is supported by sound signals and multicolor LED diode. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire.

Upgrade kit works without problems with any battery from 7V do 17V. It can also be used with most extreme setups, without any limitations as to the spring rating.

ARVOSTELUT

Arvostelujen yhteenveto

(0/5)

Yhteensä 0 arvostelua

0%
0%
0%
0%
0%
Tuotteella ei ole vielä yhtään arvostelua.Kirjaudu sisään ja arvostele tuote.
logo

ASIAKASPALVELU

Kuluttaja-asiakkaat:
asiakaspalvelu@milgear.fi
P. 045 1100131 (ti-pe 12-16)

Yritys- ja viranomaisasiakkaat sekä jälleenmyyjätiedustelut:
myynti@milgear.fi
P. 045 1100131 (ti-pe 12-16)

Jos asiasi on kiireellinen, etkä tavoita meitä puhelimitse, laitathan meille sähköpostia.

MILGEAR MYYMÄLÄ

Isokatu 56
90100 OULU

Avoinna:
tiistai - perjantai
klo 12.00-17.00

Poikkeusaukioloajat:
Suljettu - Perjantai 29.03.2024
Suljettu - Keskiviikko 1.5.2024
Suljettu - Torstai 9.5.2024
© MILGEAR Finland 2024. All rights reserved.
facebookyoutubeinstagram